87240 DC/DC displacement transducer

For displacement and all mechanicals values which can be converted to displacements, integrated amplifier, free of hysteresis, large temperature range

Product Inquiry

    Product comparison

      • Features

        • Ranges 0 ... ± 1.27 mm to 0 ... ± 76.20 mm
        • Integrated amplifier
        • Free of hysteresis
        • Large temperature range from -50° C ... 120° C
        • Suitable for operation in hydraulic fluid up to 3 bar
        • Protection IP64
      • Product data

        Model 87240
        Principle Inductive
        Measuring range

        0 … ± 1.27 mm
        0 … ± 1.8 mm
        0 … ± 2.54 mm
        0 … ± 3.8 mm
        0 … ± 6.35 mm
        0 … ± 9.5 mm
        0 … ± 12.70 mm
        0 … ± 19.0 mm
        0 … ± 25.40 mm
        0 … ± 38.1 mm
        0 … ± 50.80 mm
        0 … ± 69.5 mm
        0 … ± 76.20 mm
        0 … ± 82.5 mm

        Signal output see data sheet
        Protection class IP64
        Range of operating temperature -50 ... +120 °C
        Excitation voltage 6 ... 30 VDC
        Electrical connection

        4 teflon insulated wires

        Return spring No
        Specific characteristics

        • Integrated amplifier
        • Free of hysteresis
        • Suitable for operation in hydraulic fluid up to 3 bar
      • Description

        Displacement and all mechanical values which can be converted to displacements (e.g. compressive and tensile force, strain, torque and vibration) may be measured by this DC/DC displacement sensor. Typical application areas are the measurement of displacement and strain on machines, servo systems, vehicles, on test plants, in civil engineering and tunnel construction.

        An integrated maintenance-free electronic and a high-level DC output signal provide an easy handling without any problems.

        Displacement sensors of series 87240 convert a displacement into an analog electrical signal. They consist of a differential transformer with moveable core, an oscillator and a demodulator. These components are integrated and encapsulated in a cylindrical housing made of stainless steel. The sensors are energized by DC voltage, which is converted to AC by the oscillator and brought to the primary coil of differential transformer. The voltages induced by the two secondary windings of the transformer are demodulated, filtered and switched inverse to each other. The result is a 0 V signal, if the core is in the center position.

        The direction of an axial core displacement is shown by the polarity of the output voltage. The amplitude of the voltage changes proportional to the magnitude of the core’s displacement and respectively to the measured deflection.

        In and output terminals of the displacement sensor are galvanically insulated and there is no connection to the housing of the sensor.

        The mounting of the DC/DC displacement sensor will be done e.g. by a clip enclosing the sensor’s housing. The dynamic unit to be measured should be connected to the core of the sensor. To avoid an influence to the magnetic field and the measured value, coupling elements have to consist of a non magnetizable material like brass, aluminium or non-magnetizable steel.

      • Data Sheet & Downloads

        Data sheet
        Further info



      burster in Germany

      burster praezisionsmesstechnik gmbh & co kg
      +49 7224645-0
      infoburster.com
      www.burster.com

      Company-Information Company-Information

      Germany

      burster praezisionsmesstechnik gmbh & co kg

      Talstr. 1-5
      76593 Gernsbach
      Germany

      Fon: +49 7224645-0
      Fax: +49 7224645-88
      infoburster.com
      www.burster.com

      Trade fairs

      Motek
      04.10. - 07.10.22 - Stuttgart, 70269, Germany  

      ×
      © 2022 // burster präzisionsmesstechnik gmbh & co kg
      nach oben