8411 Cella di carico subminiatura

Molto compatta, di piccole dimensioni, robusta, resistente, per misure in trazione e compressione, in acciaio inossidabile

Richiedi prodotto

    Confronta prodotto

      • Features

        • Dimensioni molto piccole
        • Costruzione robusta
        • Prodotta in acciaio inossidabile
        • Alta frequenza di risposta
        • Per misure in trazione e compressione
        • Deviazione curve caratteristiche < 0.5% F.S.
      • Product data

        Model 8411
        Measuring range

        0 … 2,5 N
        0 … 5 N
        0 … 10 N
        0 … 20 N
        0 … 50 N
        0 … 100 N
        0 … 200 N
        0 … 500 N
        0 … 1000 N
        0 … 2000 N
        0 … 5000 N

        Direction of force Tension and compression
        Standardization Option
        Signal output

        2 mV/V
        15 mV/V
        depending on measuring range

        Protection class IP54
        Overload protection No
        Pull-plate No
        Load introduction button No
        Range of operating temperature -55 ... +120 °C
        Specific characteristics

        • Very small dimensions
        • Robust construction
        • Made of stainless steel
        • High resonance frequency
        • Characteristic curve deviation < 0.5% F.S.
      • Description

        The sensors series 8411 have deliberately been given small dimensions, so that they can easily be incorporated into existing structures or fitted into locations where access is difficult. Tensile and compressive forces are introduced to the cylindrical sensor housing through the two threaded bolts. Typical applications for these subminiature load cells include their use as measuring devices in equipment construction in general, in production lines, in measurement and control equipment, test equipment and so forth.

        The sensor is to be carefully screwed into place using the threaded bolts. Tools must not be used for assembly.

        The force must only be applied centrally, along the center line, and only through the threads. Other fitted parts must not touch the sensor housing; it is recommended that adhesive is applied to the threads. Bending, flexing or torsion forces will cause errors in the measurements and can damage the sensor. To avoid overload during assembly, it is helpful if electrical connections are made to the sensor beforehand and if the measurement on the display is watched during the process.

        The forces to be measured are applied centrally to the load cell through the two threaded pins. One covering surface of the cylindrical sensor housing is implemented as a measuring element, with the strain gauge being applied to its inner side. Under the influence of force, the full bridge circuit is unbalanced, and an output signal proportional to the force is generated.

        A rigid compensation circuit board, 7 mm wide and 70 mmlong, is located in the connecting cable to the sensor about 900 mm from the sensor body. This contains a resistor network for balancing the bridge and for temperature compensation. Removing the circuit board, or changing the cable length, will disturb the sensor‘s calibration figures.

        The strong, rigid design leads to high natural frequencies up to 160 kHz as a result, which is beneficial for dynamic measurements. The active side is the thread next to the cable.

      • Data Sheet & Downloads

        Data sheet
        Brochure
        Further info
      • Accessories

        pdf Rod ends with internal/external thread for force introduction
      • Videos

        Example showing load cell fitted under pre-load using quick-change device


        Youtube channel Burster Youtube Channel

      Related products




      Riferimenti

      Nuova brochure: Press-fitting - the reliable way

      Scoprite la nuova brochure Press-fitting - the reliable way. Controllo di qualità al 100% per le operazioni di pressatura manuale con molti esempi applicativi e informazioni focalizzate sul prodotto!

      Download our new brochure

      Brandnew: Torque Measurement Brochure

      Scoprite la nostra nuova brochure Torque Sensor con molti esempi applicativi e informazioni focalizzate sul prodotto!

      Download our new brochure

      burster in Italy

      Italy

      burster Italia S.r.l.

      Via Repubblica, 10
      24035 Curno
      Italy

      Fon: +39/035/618120
      Fax: +39 035618250
      infoburster.it
      www.burster.it

      SERVICES

      • Qualified design, application support
      • Process optimization
      • Qualified integration support & training
      • On-site trouble shooting
      • Qualified phone & online support
      • Local calibration service
      ×
      © 2021 // burster Italia s.r.l.
      nach oben